IMO A12DBS-137 Pumps (2200 psi) with 30 HP Reliance Motors, Qty 9

*New Surplus*

Return to Main Equipment Page

Back To Pumps Index Page

Back to IMO Pump Index Page

IMO A12DBS-137 Pump

ROTARY SCREW PUMPS - 12D SERIES - THREE SCREW PUMPS

The reliable pump people
Imo Series 12D Pump
INLET ROTATABLE IN 90° INCREMENTS FOR EASE OF PIPING
REPLACEABLE ROTOR HOUSINGS FOR EASE OF REPAIR
HARDENED BALANCE PISTON - NEGATES THE EFFECT OF DISCHARGE PRESSURE ON POWER ROTOR AXIAL THRUST
IDLER ROTOR BALANCE CUP - NEGATES THE EFFECT OF DISCHARGE PRESSURE ON IDLER ROTOR AXIAL THRUST
CASE HARDENED THREAD GROUND SCREWS FOR DURABLE OPERATION
RUGGED DUCTILE IRON CASING.
SINGLE, EXTERNAL, PREMANENTLY GREASE PACKED BALL BEARING POWER ROTOR SHAFT
SINGLE MECHANICAL SEAL VENTED TO INLET PRESSURE
IDLER ROTORS
Casing High shock capacity ductile (nodular) iron.
Rotor Housing Pearlitic gray iron on sizes 137.
Power Rotor Alloy steel, nitride hardened and thread ground
Idler Rotors Pearlitic gray iron, hardened and thread ground, size 137
Gaskets Cellulose and non-asbestos fiber
Shaft Seal & Bearing: Type B: Buna N bellows mechanical seal, Buna N O-rings and standard external, permanently grease packed, deep groove ball bearing - recommended for distillate fuels and lubricating oil or hydraulic fluids.
Type H: Positive drive mechanical seal, Viton O-rings and external high temperature,
permanently grease packed, deep groove ball bearing.
Outlet Pressure 1500 PSIG (103 BAR) maximum for distillate & residual fuels and crude oils. 2200 PSIG (152 BAR) for lube, seal and hydraulic fluids. Minimum recommended differential pressure is 40 PSI (2.8 BAR) when viscosity > 100 ssu.
Inlet Pressure Type B & H: 75 PSIG (5 BAR) maximum, distillate fuel, lube- sizes 106-187
Type H: 40 PSIG (2.7 BAR) maximum, residuals and crude oil- sizes 106-187
Viscosity 33 SSU (2.0 CST) minimum
Type B: 3000 SSU (650 CST) maximum (consider cold start)
Type H: Viscosities above 3000 SSU (650 CST)
Temperature Type B: 0 to180°F (-18° to 82°C) Type H: 0 to 250°F (-18 to 121°C)
Speed See curve termination for maximum speed. Do not exceed 1800 RPM when pumping residual fuels or crude oil due to the presence of abrasives and contaminants.
Drive Direct only.
Rotation Clockwise facing pump shaft standard.
Mounting May be foot mounted in any orientation.
Filtration Inlet strainers are required to keep contaminants and abrasives out of the pump and must be selected in consultation with the strainer vendor to prevent pump starvation. Normally, 60 mesh (0.01 inch- 238 micron) for light and 1/8-3/16 inch (3-5mm) openings for heavy oils are recommended. Return line filters for closed loop systems also recommended.

Motor: Reliance 30 HP, 2940 RPM, 380V/50Hz/3Phase, 41.2 Amps, TEFC Enclosure, Continuous Duty, Safety Factor: 1.15. Frame: 286TS, ID: 1MAF65558.

Specifications
Series 12D Imo pumps are intended for relatively high pressure service on petroleum or similar viscosity liquids. Typical applications include crude oil pipeline service, fuel atomization for burning in a steam boiler, fuel injection for combustion gas turbines, fluid power service on hydraulically operated machinery, gas sealing in centrifugal compressors and hydrostatic bearing support. These pumps are hydraulically balanced in both the axial and radial directions which eliminates bearing loads due to discharge pressure. The single bearing is external to the liquid pumped and does not rely on the lubricating qualities of the pumped liquid. The single mechanical seal is exposed only to inlet pressure. Very low airborne noise levels are normal for Imo three screw positive displacement pumps as are high operating efficiencies and non-pulsating delivery of flow.

Originally paid $3,369.00 each. NOW SAVE 35%.

Your Price: $2,190.00 each (New Surplus)